Microstructural changes accompanying repair welding in 5xxx aluminium alloys and their effect on the mechanical properties

At the shipyards, the aluminium alloy 5083 is welded with a multi-pass sequence using the metal inert gas technique. If, while checking the weld integrity either after welding or during service, defects are detected in the vicinity of the weldment, repairs are usually employed to extend the service life.

The repair method involves removal of the upper passes, depending on the thickness and re-welding under the same conditions.

Purpose of this paper is to examine the microstructural changes accompanying repair welding, define their effect on properties of primary importance and set, if possible, an upper limit as far as the number of repairs is concerned.     

Experimental investigation of the normal spectral emissivity and other thermophysical properties of pulse-heated Ni-Ti and Au-Ni alloys into the liquid phase

1. Introduction Metal working industry needs accurate thermo- physical properties of liquid metals and alloys as input data for different simulation routines to im- prove the performance of their products. Within this paper we continue the systematic investigation of the dependence of emissivity of binary alloys on the relative concentration of the constituent elements (for a previous paper see [1]). 2. Experimental method A fast ohmic pulse heating technique is applied to heat metallic wire-s…     

亚硝酸钠作释放剂选择性螯合滴定法测定钯

用EDTA螯合Pd^2 和其它金属离子，然后用亚硝酸钠分解Pd—EDTA螯合物，释放出的ED—TA用Zn^2 标准溶液进行返滴定。大量各种金属离子都不干扰。用于测定Pd—Cu合金镀层、Pd—Sn—Cu合金镀层和Pd—Ti—Si合金中的钯，获得相当满意的结果。     

Dental amalgam – the effect of the technology of alloy powder preparation on the corrosion behaviour and the release of mercury

Dental amalgams are based on a broad spectrum of materials differing in their chemical composition, metallurgical treatment, and in the way the initial alloys powders are prepared. In addition to their chemical composition, amalgams based on various powders differ in both their microstructure and the amount of mercury needed for preparation. All these facts may affect electrochemical processes occurring during their interaction with oral fluids, and also mercury release. While verifying the effect of the technology used for the preparation of the high‐copper ternary alloy powder on the properties of resulting amalgams, this study aimed at the mechanism of their interaction with a model saliva solution as well as mercury release was included. Measurements were done in a model saliva solution using standard electrochemical methods and exposition measurements. The interaction of individual types of amalgams with artificial saliva did not reveal any significant differences. The free corrosion potential of all these amalgams in an aerated solution settled in the range of values in which tin oxidation, resulting in a layer of insoluble corrosion producsts, turned out to be the dominant anodic process. The rate of mercury release was the lowest for amalgams based on a gas‐atomized alloy. The highest rate of mercury release, and also its dependence on time, was exhibited by lathe‐cut powder based amalgam. In addition to different volume fraction of the Ag‐Hg phase and the level of its tin alloying, this different behaviour may be explained by differences in the rate at which a layer of tin corrosion products acting as a barrier to mercury release is formed.     

The hydrogenation of triglycerides using supported alloy catalysts. I. Silica-supported Ni—Ag catalysts

Silica-supported Ni-Ag catalysts with a loading of 2·1·0.6% (w/w) total metal have been prepared using the precursors nickel dimethylglyoxime and silver nitrate by means of a simple impregnation method. The resulting catalysts were activated by calcination at 260°C in air, followed by hydrogen reduction at 450°C. They were then employed for soyabean oil hydrogenation at 1 bar H2 pressure and 160°C in a stirred batch reactor. Characterisation of the catalysts using temperature-programmed reduction and electron microscopy indicated that alloying of nickel and silver had occurred, but metal particle composition, for a given overall composition, varied with metal particle size and smaller metal particles were nickel rich. The hydrogenation activity and selectivity measurements revealed that the catalysts were more active and selective than a commercial nickel catalyst. Furthermore, the specific activities of the alloy catalysts were a maximum for alloys in the range 70–90 at. % Ni. However, the supported alloy catalysts also gave rise to greater trans isomerisation than the commercial catalyst. This is attributed to hydrogen deficiency caused by large triglyceride molecules blocking hydrogen chemisorption on small nickel particles (10–50 Å in diameter), leading to enhanced cis-trans isomerisation.     

住宅建筑带钢副框铝合金门窗防渗漏施工技术

使用自粘性防水卷材对带钢副框的铝合金门窗窗边进行粘接,以防止雨水通过副框与墙体之间的缝隙渗漏到室内,重点介绍了详细的施工措施。     

铝合金穿孔板吸声墙面施工技术

以教育部综合办公楼工程的机房铝合金穿孔板吸声墙面施工为例,介绍其固定件及吸声墙面的做法。     

High-performance polymer alloys of polybenzoxazine and bismaleimide

Two series of high-performance polymer alloys were prepared by mixing typical benzoxine monomers, 3-phenyl-3,4-dihydro-2H-1,3-benzoxazine (P-a) or 6,6-(1-methylethyliden)-bis-(3,4-dihydro-3-phenyl-2H-1,3-benzoxazine) (B-a), with a typical bismaleimide, 4,4-bismaleimidodiphenyl methane by various ratios followed by thermal treatment up to 240 °C. DSC and IR of the alloys were examined to follow the curing reaction. These analyses showed that the obtained polymer alloys are AB co-cross-linked polymer networks through the formation of ether linkage between the hydroxyl group of polybenoxazine and the double bond of bismaleimide. Viscoelastic analysis and softening temperature measurement revealed that the polymer alloys have much higher glass transition temperatures than those of each homopolymer. The thermal stability also increased with the increase of bismaleimide content as evidenced by TGA.     

全封闭Ar气保护电渣重熔GH4169合金

上海五钢采用ALD 5t全封闭Ar气保护电渣重熔炉 ESR(Ar)冶炼了GH4 16 9合金锭 ,分析结果表明 ,ESR(Ar)电渣锭氧、硫含量和锭头尾碳、铝、钛之差远低于一般ESR工艺 ;VIM(真空感应熔炼 ) +ESR(Ar)工艺冶炼合金中平均氧含量 6× 10 - 6 远低于VIM +VAR(真空电弧重熔 )工艺冶炼合金中平均氧含量 13× 10 - 6 ,所以ESR(Ar)工艺脱氧效果优于VAR工艺     

烧结硬化用低合金钢粉

本文将介绍三种不同成分的低合金钢粉。在混入2 0%铜和不同石墨含量的条件下,对该三种粉进行了试验评定。试件的密度为6 9g/cm3,在氮氢混合气氛中于1120℃下烧结25min,在炉内冷却带650～400℃温区的冷却速度为0 4或1 5℃/s条件下,对烧结态和回火后试件的力学性能进行了测试。回火条件为200℃下保温60min。在一定的冷却速率和碳含量条件下,各种钢粉烧结后的硬度可高达40HRC。回火后,硬度仍可以保持在30HRC以上。